Skip to content

PoE Security Camera Guide: How One Cable Powers Your CCTV (2026)

PoE Security Camera Guide: How One Cable Powers Your CCTV (2026)
TSE Expert|

A PoE security camera gets its power and its network connection through a single Cat6 cable, so there is no power point needed at the camera. The cable runs back to a PoE switch or an NVR with built-in PoE ports, which records the footage. It is the standard choice for wired home and business CCTV in Australia because it is stable, tidy and does not rely on Wi-Fi.

PoE works well when it is planned properly. This guide covers how it works, what you need, and the limits many guides skip: cable length, power budget, cheap cable and night-time power draw.

How a PoE Security Camera Works

PoE stands for Power over Ethernet. A normal network cable has four twisted pairs of copper wire. With PoE, the device at the other end (the switch or NVR) sends low-voltage DC power down those same pairs alongside the video data. The camera negotiates how much power it needs, and the switch supplies it.

There are a few PoE standards. The two you will see most on CCTV gear are:

  • 802.3af (PoE): enough for most fixed dome, turret and bullet cameras.
  • 802.3at (PoE+): more headroom, needed for some cameras with heaters, strong white-light or larger IR, and for many PTZ models (larger PTZs may need PoE++ or their own power supply).

Always check the camera's datasheet for its PoE class and maximum power, not just the word "PoE".

PoE vs Wi-Fi Security Cameras

Wi-Fi and battery cameras are quick to put up, but they still need power and depend on the signal at that spot. Brick walls, metal cladding and distance from the router all matter.

Factor PoE (wired) Wi-Fi / battery
Connection Steady, not affected by Wi-Fi drop-outs Depends on signal strength and interference
Power From the switch or NVR, no charging Power point nearby, or battery/solar to maintain
Recording Usually continuous to an NVR on site Often motion clips only, sometimes cloud-based
Install effort Cable runs needed (easiest at build or reno) Fast to mount and move
Best for Permanent systems, multiple cameras, businesses Rentals, one or two cameras, hard-to-cable spots

For a step-by-step look at the other choices before a system goes in, see our installation checklist.

What You Need for a PoE Camera System

  • Cameras rated for where they are going. Outdoor security cameras should have a weather rating such as IP66 or IP67.
  • A recorder. An NVR with built-in PoE ports is the simplest setup for smaller sites. An 8 channel NVR kit suits most houses and small shops.
  • A PoE switch for CCTV when you need more ports, longer layouts or cameras spread across a building.
  • Solid copper Cat6, plus quality RJ45 plugs, junction boxes and mounting brackets.
  • A hard drive sized for how many days you want to keep. Our guide on how much storage you need explains the maths.

The Real Limits of PoE (What Often Goes Wrong)

1. The 100 metre cable limit

Standard Ethernet, and PoE with it, is designed for runs of up to 100 metres, including patch leads. Go past that and you can get dropped video or a camera that will not power up. For a long driveway or a shed, use an inline PoE extender or plan a switch closer to the cameras. Fibre is the usual answer between separate buildings.

2. The power budget

Every PoE switch and NVR has a total power budget shared across its ports. Having eight ports does not mean it can run eight of any camera. For example, a camera rated at up to 9.5W, multiplied by eight, is 76W. A switch with a 63W total budget would be short at full load. Add up the maximum draw of every camera, then leave around 20% spare.

3. Night-time power draw

A night vision security camera uses more power once its infrared or white-light LEDs switch on. A system that runs fine during the day can start rebooting cameras after dark if the budget was worked out on daytime figures. This is one of the most common "my cameras go offline at night" calls. Larger sites have more to manage here, which we cover in PoE budgeting for 100+ camera sites.

4. Cheap cable (CCA)

Some low-cost "Cat6" is copper-clad aluminium (CCA), not solid copper. It has higher resistance, so more voltage is lost along the run. Data may still pass on a laptop test while the camera fails to power up properly. Use solid copper Cat6 UTP cable from a known source, and terminate both ends to the same standard (T568B is the most common).

5. Night range and image quality are separate questions

PoE only delivers power and data. It does not improve the camera itself. The infrared range on the spec sheet is a best-case figure, and faces or number plates are only identifiable at a fraction of that distance. Choose the lens and placement for what you actually need to see.

6. Who can run the cable

In Australia, data cabling that connects to the telecommunications network (for example, an NVR plugged into your NBN router) generally needs to be installed by an ACMA-registered cabler. That is another good reason for homeowners to use a qualified installer rather than going fully DIY.

Recommended Products from TSE

These are stocked for installers and trade customers. Specs below are as listed on each product page.

Need more ports? Browse our full range of PoE switches.

Why Choose Total Security Equipment

Total Security Equipment is a wholesale supplier to security installers, electricians and integrators across Melbourne and Sydney. We stock matching PoE cameras, NVRs, switches, cable and brackets, and our team can help you check a PoE power budget before the job, not after the first callback.

Installer or trade buyer with an upcoming CCTV project? Open a trade account or call us to talk through the design. Homeowner? Ask your installer about a wired PoE system and whether the switch has enough power for your cameras at night.

📍 26 Davies Ave, Sunshine North, VIC 3020
📞 03 9079 5566

Call us or send a message for trade pricing and technical advice.

PoE Security Camera FAQs

1. Does a PoE camera need a power point?

No. It is powered through the network cable from a PoE switch, PoE NVR or PoE injector. Only the switch or NVR needs mains power.

2. Can I plug a PoE camera into my normal home router?

Most home routers do not supply PoE, so the camera will not power up. You need a PoE switch, a PoE NVR or an injector between them.

3. How far can a PoE camera be from the NVR?

Up to 100 metres of cable is the standard design limit. Beyond that, use a PoE extender, a switch closer to the camera, or fibre between buildings.

4. Why do my PoE cameras drop out at night?

The most common causes are a switch or NVR running out of PoE power once IR switches on, long runs near the 100 m limit, CCA cable or poor terminations.

5. Will a PoE system still record if the internet goes down?

Yes, if it records to a local NVR. You lose remote viewing until the internet is back, but recording continues. A UPS keeps it running through short power cuts.

Additional Information

Melbourne HQ

26 Davies Ave., Sunshine North, VIC 3020
03 9079 5566

Sydney Branch

38 Lisbon St., Fairfield East, NSW 2165
02 8722 0348

Ordering & Support

  • Australia-wide prompt shipping
  • 100% genuine official stock with full local warranty
  • Matching NVRs, junction boxes & brackets in stock
  • Trade accounts and installer discounts available
  • Professional technical guidance on positioning & network design

Need expert assistance choosing the right PoE cameras, switches and NVRs for your site? Contact our Melbourne team on 03 9079 5566 or Sydney on 02 8722 0348 for technical advice.

Back to blog
You might like